Posts Tagged ‘priority-queuing’

Sep
16

The security appliance supports two kinds of priority queuing – standard priority queuing and hierarchical priority queuing. Let’s configure each in this third part of our blog.

Standard Priority Queuing

This queuing approach allows you to place your priority traffic in a priority queue, while all other traffic is placed in a best effort queue. You can police all other traffic if needed.

Step 1: Create the priority queue on the interface where you want to configure the standard priority queuing. This is done in global configuration mode with the priority-queue interface_name command. Notice this will place you in priority queue configuration mode where you can optionally manipulate the size of the queue with the queue-limit number_of_packets command. You can also optionally set the depth of the hardware queue with the tx-ring-limit number_of_packets command. Remember that the hardware queue forwards packets until full, and then queuing is handled by the software queue (composed of the priority and best effort queues).

pixfirewall(config)# priority-queue outside
pixfirewall(config-priority-queue)#

Step 2: Use the Modular Policy Framework (covered in Part 2 of these blogs) to configure the prioritized traffic.

pixfirewall(config-priority-queue)# exit
pixfirewall(config)# class-map CM-VOICE
pixfirewall(config-cmap)# match dscp ef
pixfirewall(config-cmap)# exit
pixfirewall(config)# class-map CM-VOICE-SIGNAL
pixfirewall(config-cmap)# match dscp af31
pixfirewall(config-cmap)# exit
pixfirewall(config)# policy-map PM-VOICE-TRAFFIC
pixfirewall(config-pmap)# class CM-VOICE
pixfirewall(config-pmap-c)# priority
pixfirewall(config-pmap-c)# exit
pixfirewall(config-pmap)# class CM-VOICE-SIGNAL
pixfirewall(config-pmap-c)# priority
pixfirewall(config-pmap-c)# exit
pixfirewall(config-pmap)# exit
pixfirewall(config)# service-policy PM-VOICE-TRAFFIC interface outside
pixfirewall(config)# end

Hierarchical Priority Queuing

This queuing approach allows you to shape traffic and allow a subset of the shaped traffic to be prioritized. I have cleared the configuration from the security appliance in preparation for this new configuration. Notice with this approach, you do not configure a priority queue on the interface. Also notice with this approach the nesting of the Policy Maps.

pixfirewall(config)# class-map CM-VOICE
pixfirewall(config-cmap)# match dscp ef
pixfirewall(config-cmap)# exit
pixfirewall(config)# class-map CM-VOICE-SIGNAL
pixfirewall(config-cmap)# match dscp af31
pixfirewall(config-cmap)# exit
pixfirewall(config)# policy-map PM-VOICE-TRAFFIC
pixfirewall(config-pmap)# class CM-VOICE
pixfirewall(config-pmap-c)# priority
pixfirewall(config-pmap-c)# exit
pixfirewall(config-pmap)# class CM-VOICE-SIGNAL
pixfirewall(config-pmap-c)# priority
pixfirewall(config-pmap-c)# exit
pixfirewall(config-pmap)# exit
pixfirewall(config)# policy-map PM-ALL-TRAFFIC-SHAPE
pixfirewall(config-pmap)# class class-default
pixfirewall(config-pmap-c)# shape average 2000000 16000
pixfirewall(config-pmap-c)# service-policy PM-VOICE-TRAFFIC
pixfirewall(config-pmap-c)# exit
pixfirewall(config-pmap)# service-policy PM-ALL-TRAFFIC-SHAPE interface outside
pixfirewall(config)# end

Verifications for Priority Queuing

These verification commands can be used for both forms of priority queuing. Obviously, you can examine portions of the running configuration to confirm your Modular Policy Framework components. For example:

pixfirewall# show run policy-map
!
policy-map PM-VOICE-TRAFFIC
 class CM-VOICE
  priority
 class CM-VOICE-SIGNAL
  priority
 class class-default
policy-map PM-ALL-TRAFFIC-SHAPE
 class class-default
  shape average 2000000 16000
  service-policy PM-VOICE-TRAFFIC
!

Another example:

pixfirewall# show run class-map
!
class-map CM-VOICE-SIGNAL
 match dscp af31
class-map CM-VOICE
 match dscp ef
!

To verify the statistics of the standard priority queuing configuration, use the following:

pixfirewall# show service-policy priority
Interface outside:
  Service-policy: PM-VOICE-TRAFFIC
   Class-map: CM-VOICE
      Priority:
        Interface outside: aggregate drop 0, aggregate transmit 0
    Class-map: CM-VOICE-SIGNAL
      Priority:
        Interface outside: aggregate drop 0, aggregate transmit 0

You can also view the priority queue statistics for an interface using the following:

pixfirewall# show priority-queue statistics outside
Priority-Queue Statistics interface outside
Queue Type         = BE
Tail Drops         = 0
Reset Drops        = 0
Packets Transmit   = 0
Packets Enqueued   = 0
Current Q Length   = 0
Max Q Length       = 0
Queue Type         = LLQ
|Tail Drops         = 0
Reset Drops        = 0
Packets Transmit   = 0
Packets Enqueued   = 0
Current Q Length   = 0
Max Q Length       = 0

To verify the statistics on the shaping you have done with the hierarchical priority queuing, use the following:

pixfirewall# show service-policy shape
Interface outside:
  Service-policy: PM-ALL-TRAFFIC-SHAPE
    Class-map: class-default
      shape (average) cir 2000000, bc 16000, be 16000
      (pkts output/bytes output) 0/0
      (total drops/no-buffer drops) 0/0
      Service-policy: PM-VOICE-TRAFFIC

The next blog entry on this subject will focus on the shape tool available on the PIX/ASA.

Thanks so much for reading!

Tags: , , , ,

Categories

CCIE Bloggers